When the driver gets out of the car, he opens the door without confirming whether the car is coming from behind, causing serious car accident injuries. Basically, most of these accidents are caused by the driver's negligence. It is undeniable that if everyone is more vigilant, it may also be possible to reduce accidents However, when discussing the ratio of liability, we can actually make some changes to reduce the possibility of accidents and ensure everyone's driving safety, right?During the installation process, in order to satisfy the overall texture after installation, the door panel must be disassembled during the process. It is recommended that you look for relevant precautions and disassembly points before operating the installation to avoid disassembling the wrong parts and damaging the door panel or trim panel. Most car door panels Most of the dismantling process has relevant information to find, just be patient to find it.Operation point 1: No matter where the light bar is attached, it is strongly recommended that the location where the LED light bar is attached should be cleaned as much as possible without damaging the surrounding interior or car paint, so as to prevent the light bar from falling off.Operation point 2: Install the LED light strips around the door. Based on the author's personal experience, the ceremonial lights on the original car door will be used for power connection. If the original car does not have this designer, it must be connected to the power supply from the inside of the car door light accessories.Operation point 3: When installing modified items around the door, the most common disassembly is the door inner panel. During the disassembly process, remember not to forcefully disassemble it. Please confirm that each locking screw has been removed before proceeding with the disassembly.Triangular window trim panel removal, most car door triangular windows have interior trim panels installed, the removal process does not require tools, just need to carefully confirm the foot position, and pull it out with one force.When the door switch screws are removed, most cars will have some slight decoration inside the door, which makes people unable to find the screw position for a while. Before removing the door handle screw, pay more attention to find it.The door armrest screws are removed. Of course, there will be screw locks in this position. Of course, there will be decorative panels covering the screws. You can find the location by searching carefully. However, the design of each car model is different.After the door trim panel screws are removed, you can use your fingers or a special crowbar for the door trim panel to open the door trim panel. After pulling it open, push the door trim panel upwards to separate it from the door.The door pull rope removes the linkage switch. The steel rope of the door must be removed at this time to facilitate subsequent follow-up operations. Because each car has a different design, if it cannot be removed, do not force it.To facilitate the operation, it is strongly recommended to remove all switch wire groups on the door, so as to facilitate the rotation of the door trim panel, so as not to allow the wire groups to follow the winding and avoid damage to the wire groups.Power supply wiring Most cars have door etiquette lights design, we can directly use the power supply here, but if not, we must pass through the door coil to connect the interior light power supply to the car.Of course, for the convenience of dismantling the ceremonial light line group, you can freely choose whether to carry out this operation or not. If you do not carry out this operation, you must carry the door panel wiring operation.Light bar connection test Because the LED light bar has positive and negative polarities, it is best to use a three-meter to confirm, but if you miss the preparation, you can also jump to confirm which line will operate normally.After the power supply confirms which line is crossed, you can dial the line to cross, and some car owners do not like to destroy the original car.When attaching the light bar, please be careful not to set it too high, otherwise it will be damaged by other parts of the door, and it will be a waste of effort!After the light bar is confirmed to be attached, it is recommended to connect the power supply first and conduct a power-on actuation test. In addition to avoiding the occurrence of wrong installation, it can also confirm the effect of the light-emitting warning. If you are not satisfied, you can adjust it again.After there is no problem in the storage test of the redundant wire group, the reserved wire group can be stored. We can use a small strap to tie the reserved wire group together and tighten it for future adjustment.When the reassembly is completed, the previously disassembled wire sets and pull ropes must be reassembled one by one, and they must be properly installed, otherwise there will be a dilemma that the door cannot be opened in the car!